SLASH® ONE SHOT | Aluminum Crossbow Bolts
$ 29.99 $ 39.99
Slash Express Arrow Sale
For the entire month of December, if you buy 2 packs of our Slash Express Arrows, you will receive (1) pack of Slash Express Arrows & (1) pack of broadheads for FREE!
Offer is valid through 12/1/22 until 11:59pm of 12/31/22.
WARNING! Read these instructions before shooting a SLASH® INsetBlade® Arrow.
WARNING! Prior to use, SLASH® INsetBlade® Arrows should be slowly and gradually flexed to ensure structural integrity, and thoroughly inspected for loose components and/or damage, such as shaft splitting, deformation, or delamination. Using damaged shafts/arrows, or arrows with loose components, can cause serious injury or death and should not be used under any circumstances. After a first use, it is very important to carefully inspect the shaft/arrow and components, as damage may not be readily apparent. If you are not certain of the structural integrity and proper function of the shaft/arrow and components, the arrow should not be reused.
DO NOT SHOOT ARROW IF YOU SEE ANY CRACKS ON THE ARROW SHAFT.
Please read these instructions prior to attempting to use these SLASH® INsetBlade® Arrows. Should you have any questions regarding their use or setup, please contact one of our customer service representatives at 713-444-0788
BLADE ALIGNMENT
For the best arrow flight and accuracy, the blades of the broadhead should be aligned with the vanes on the arrow (see Figure 1). For the INsetBlade® Deployable Blades (the blades within the arrow shaft) to function and deploy properly, the INsetBlade® tabs must be offset from the blades of the broadhead in front of them. The broadhead blades MUST NOT align with, or be in front of, the INsetBlade® tabs behind them (see Figure 1).

The cock vane (single color vane) and the top broadhead blade should be UP (see Fig 2).
The INsetBlade® tabs should be at a 90° side angle to the top broadhead blade and cock vane. NOTE proper position of Retention O-ring.
SETUP INSTRUCTIONS
SLASH® INsetBlade® Arrows come pre-assembled but are available unassembled as well. For proper setup, follow these instructions.
For optimal performance, you must align the broadhead blades to the vanes and offset the INsetBlade® Deployable Blades from the broadhead blades. Likewise, the bowstring and nock must be aligned with the top cock vane, maintaining the 90° offset of the INsetBlade®tabs.
PROPER SETUP:
- Using a broadhead wrench, screw the broadhead onto the arrow, noting where the position where the blades stop.
- Tighten the broadhead until one of the blades is pointing up at a 90° angle (perpendicular) to the flat edge of the INsetBlade® tabs. The INsetBlade® tabs are small, triangular points extending outward from the shaft when in the closed position. Broadhead blades SHOULD NOT be in line with these INsetBlade® tabs.
- When installing vanes, ensure the cock vane is in line with the bowstring when nocked and is also in line with the top broadhead blade to maintain the 90° angle offset of the INsetBlade® tabs. When nocked, the INsetBlade® tabs should be horizontal.
WARNING! Ensure the INsetBlade® Retention O-ring is installed in its proper location relative to the blades (see Figure 6), prior to shooting. NEVER draw the INsetBlade® Deployable Blades past your bow-holding hand or arrow rest (see Figure 4).
BROADHEAD ASSEMBLY
In the event you need to assemble the broadhead for your SLASH® INsetBlade® Arrow, follow these instructions.
WARNING! Broadhead blades are extremely sharp. Care should be taken to handle them as such. Mishandling will result in serious injury!
Hold the broadhead ferrule [A] in the up position.
Place the broadhead blades [B] pointing up and slide them into position under the trocar tip and carefully set them into the grooves of the ferrule.
Slide the retaining ring [C] up the bottom of the ferrule and lock the blades [B] in place. The ring should completely cover the bottom tabs of the blades.
Slide the washer [D] up the bottom of the ferrule next to the retaining ring.
IMPORTANT NOTE: Be certain broadhead properly aligns with INsetBlade® Deployable Blades and vanes when screwed into arrow shaft.
WARNING! DO NOT STORE SLASH® INSETBLADE®ARROWS IN DIRECT SUNLIGHT AND/OR IN EXCESSIVE HEAT. FAILURE TO STORE THIS PRODUCT CORRECTLY MAY RESULT IN FAILURE OF THE ARROW SHAFT AND/OR THE RETENTION O-RING SYSTEM. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
KEEP BLADES OUT FRONT
SLASH® INsetBlade® Arrows are available in multiple sizes. It is extremely important to understand how a SLASH® INsetBlade® Arrow should be sized for proper and safe nocking/drawing (see Figure 5).
The INsetBlade® Deployable Blades (the blades within the arrow shaft must be securely fastened with Retention O-ring; see Figure 2) are similar to an expanding mechanical broadhead and must,at all times during the drawing and nocking process of the arrow, be in front of both the hand holding the bow and the arrow rest. DO NOT DRAW INSETBLADE® DEPLOYABLE BLADES THROUGH THE ARROW REST UNDER ANY CIRCUMSTANCES.
WARNING! FAILURE TO OBSERVE THESE SAFETY GUIDELINES MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
RECOMMENDED ARROW SIZING
WARNING! YOU MUST USE ARROWS THAT ARE DESIGNED FOR YOUR SPECIFIC DRAW LENGTH. USING ARROWS THAT ARE TOO SHORT WILL RESULT IN DAMAGE TO THE BOW AND SERIOUS PERSONAL INJURY! FAILURE TO OBSERVE THESE GUIDELINES MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
Arrow should be cut such that the INsetBlade® Deployable Blades and broadhead are all in front of the hand holding the bow handle at full draw. The tabs of the INsetBlade® Deployable Blades should always be in front of the arrow rest.*
WARNING! DO NOT USE ANY TYPE OF OVER-DRAW SYSTEM OR CROSSBOW WITH THIS ARROW.
The following are for sizing arrows. Actual cutting of arrow and proper size will be different for each archer and vary based on bow design, model and arrow rest (see Figure 5).
Do not size arrows too short at full draw.*
WARNING! DO NOT SIZE ARROW LESS THAN THE DRAW LENGTH OF THE BOW, MEASURING THE LENGTH OF THE ARROW FROM THE INSETBLADE® TABS TO THE NOCK OF THE ARROW.
Draw Length |
Total Shaft Length |
|
27" |
29" |
|
28" |
30" |
|
29" |
31" |
|
30" |
32" |
|
31" |
33" |
|
Bows with set back rests which are set back more than 2", may cut arrows 2" longer than draw length.
INSTALLING RETENTION O-RING AND INSETBLADE® DEPLOYABLE BLADES
Install the Retention O-ring to secure INsetBlade® Deployable Blades. The INsetBlade® Deployable Blades must be fully closed, the broadhead removed from the arrow, and the Retention O-ring installed properly prior to use (see Figure 6).
WARNING! FAILURE TO OBSERVE THESE SAFETY GUIDELINES MAY RESULT IN THE INSETBLADE® DEPLOYABLE BLADES OPENING DURING THE DRAW CYCLE OR DURING FLIGHT AND MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.

- Lock INsetBlade® Deployable Blades in place by closing the blades into the shaft.
- 2. Push the INsetBlade® tabs back slightly and down to lock the tips of the blades in position, completely flush with the arrow shaft.
- 3. Slide Retention O-ring over the shaft all the way back until it lies flat against the tabs as shown above, making certain it is not damaged or cut during installation (see Figure 6).
WARNING! PRIOR TO EACH USE, check the Retention O-ring for visible damage such as cracking, deformation, discoloration or any other condition that may affect its performance. If any of these conditions are present, DO NOT use. Failure to follow these instructions may result in serious injury and/or property damage.
AMO DRAW LENGTH
AMO Draw length standard is a specified distance, or the distance at the archer’s full draw, from the nocking point on the string to the pivot point on the bow grip (or theoretical vertical projection of a tangency line to the pivot point parallel to the string) plus 1 ¾ inch. Draw length from pivot point shall be designed at DLPP and shall be called true draw length. It is of the at most importance that the user have their draw length measured by a competent archery pro shop prior to purchasing these arrows.
The ONE SHOT from SLASH® Arrows is the ultimate send it and forget it crossbow bolt system. Featuring the patented SLASH® INsetBlades® integrated directly into their aluminum shafts, these crossbow bolts deliver the same devastating power as the Carbon Magnum Crossbow Bolts, but at a fraction of the cost!
Designed specifically for being a ONE SHOT use due to their aluminum shafts, these crossbow bolts are the perfect solution for the hunter who needs to sling a bunch of bolts down range at game, but isn't worried about recovering the bolts after! A hog hunter's dream come true!
NOTE: It is recommended to only shoot the hunting arrows ONCE and then discard. Aluminum shafts are very susceptible to bending or becoming damaged upon impact. Shooting them again in your crossbow could be dangerous!
Package Includes:
- 3 Aluminum Hunting Arrows SINGLE SHOT ONLY
- 2 are INsetBlade® Aluminum Hunting Arrows.
- 1 is Front-weighted Aluminum Hunting Arrow with Standard Insert to fit field tip or Broadhead.
- 1 O-Ring Set and Broadhead wrench.
- Half Moon Nock
Features:
- Revolutionary INsetBlade® Deployable Blades Technology.
- 275% larger wound channel.
- 2219 Aluminum Shaft
- All arrows matched in weight. Weight of broadhead and field tip matched.
- Double walled: carbon fiber and aluminum in the 4" section for INsetBlades®
Specifications:
- 20" crossbow bolt weighs 450 grains (without the broadhead) (510 with a SLASH 60gr broadhead)
- 2219 Aluminum Shaft
- .344 Outside Diameter
- .306 Inside Diameter
- Crescent Moon Nock
How to Size Your Bolts:
Disclaimer:
By adding to the cart, you agree that you have selected the correct cross bolt length, that you have read the safety manual and that you understand our return policy.